VAC Motorsports - Interior / Seats & Accessories / Harness Bars / All Products

Brey Krause Harness Mount Bar, Mini Cooper

Tue, 26 Apr 2022 10:07:14 GMT

Brey Krause Harness Mount Bar, Mini Cooper
Buy Now: $769.95

The Brey Krause Harness Mount Bar for Mini Cooper is an entirely new design. By making extensive use of water-jet machined sections and unique geometry, the R-1305 is our strongest and lightest harness bar of this configuration. It is also the only harness mount currently available for the Mini Cooper.

The R-1305 is a bolt-in part that requires no drilling, cutting or fabrication. It can be easily removed to allow use of the rear seat area for daily driving. The lower seat cushion can remain while the bar is installed to satisfy sanctioning bodies for autocross.

The R-1305 been tested and certified by an independent lab to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements.

Material: Type 304, stainless steel.

Finish: Powdercoated in durable black wrinkle-finish.

Weight: 16.5 lbs.

Models: Mini Cooper, Mini Cooper S 2002-2006

Installation: Bar attaches to front and rear lap belt mounting points. It can be removed for access to the rear seat (floor brackets remain in place).

Miscellaneous: Bar limits seat travel to the rear approximately 1 inch. Includes provisions for Seat Back Brace.

Visit Harness Bars to see additional products in this category.

Brey Krause Harness Mount Bar, BMW F30/F80 M3

Fri, 16 Aug 2019 08:32:47 GMT

Brey Krause Harness Mount Bar, BMW F30/F80 M3
Buy Now: $934.95

The BMW F80 harness mount bar hasbeen tested and certified by an independent lab to handle the types of forcesrequired by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev. MAR95, Motor Vehicle Seat Belt Anchorages-Performance Requirements. The BMWF80 harness mount bar properly locates and supports racing shoulderharnesses relative to the driver. In the case of an accident, it helps protectthe driver's shoulders and spine. The harness guides also prevent excessiveshifting and fatigue of the driver during the high G loads of cornering andbraking. Our bars are easy to install and remove, use only existing holes andmounting points, and will not damage the car in any way.

Strength requirements for harnessmounts are considerably greater than those for harness guide bars since theymust support the entire load applied to the belts. A mount really can't berelied on unless it has been tested to support the loads required by theNational Highway Traffic Safety Administration.

The Brey-Krause Harness Mountsupported the loads specified by the National Highway Traffic Safety Admin. DOTfor upper torso restraints in all automobiles. Tensile tests performed by anindependent lab.

Visit Harness Bars to see additional products in this category.

Brey Krause Harness Mount Bar, BMW E90/E92 Coupe

Fri, 16 Aug 2019 08:26:44 GMT

Brey Krause Harness Mount Bar, BMW E90/E92 Coupe
Buy Now: $934.95

The BMW E90/E92 harness mount bar hasbeen tested and certified by an independent lab to handle the types of forcesrequired by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev. MAR95, Motor Vehicle Seat Belt Anchorages-Performance Requirements. The BMW E90/E92 harness mount bar properly locates and supports racing shoulder harnessesrelative to the driver. In the case of an accident, it helps protect thedriver's shoulders and spine. The harness guides also prevent excessiveshifting and fatigue of the driver during the high G loads of cornering andbraking. Our bars are easy to install and remove, use only existing holes andmounting points, and will not damage the car in any way.

The Brey-Krause Harness Mount supportedthe loads specified by the National Highway Traffic Safety Admin. DOT for uppertorso restraints in all automobiles. Tensile tests performed by an independentlab.

Visit Harness Bars to see additional products in this category.

Brey Krause Harness Mount Bar, BMW F87 M2

Fri, 16 Aug 2019 08:25:58 GMT

Brey Krause Harness Mount Bar, BMW F87 M2
Buy Now: $934.95

The Brey Krause BMW F87 harness mount bar hasbeen tested and certified by an independent lab to handle the types of forcesrequired by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev.MAR95, Motor Vehicle Seat Belt Anchorages-Performance Requirements.

This BMWF87 harness mount bar properly locates and supports racing shoulderharnesses relative to the driver. In the case of an accident, it helps protectthe driver's shoulders and spine. The harness guides also prevent excessiveshifting and fatigue of the driver during the high G loads of cornering andbraking. Our bars are easy to install and remove, use only existing holes andmounting points, and will not damage the car in any way.

Visit Harness Bars to see additional products in this category.

Brey Krause Harness Mount Bar, BMW E46 Coupe

Mon, 21 Mar 2011 12:13:00 GMT

Brey Krause Harness Mount Bar, BMW E46 Coupe
Buy Now: $939.95

The Only Harness Bar we trust at VAC...

The Brey Krause E46 harness bar has been independent tested and certified by a qualified laboratory to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev. MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements.

Designed to allow use of 4, 5, or 6 point harness in your E46 M3 without the installation of a roll bar or roll cage. This bar can be removed and reattached in about 15 minutes, which makes this an ideal solution for those who still daily drive their cars.

This harness mount bar properly locates and supports racing shoulder harnesses relative to the driver. In the case of an accident, it helps protect the driver's shoulders and spine. The harness guides also prevent excessive shifting and fatigue of the driver during the high G loads of cornering and braking.
Brey Krause bars are easy to install and remove, and use only existing holes and mounting points- these will not damage the car in any way!

Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. With Brey Krause, quality and safety are #1, and are sold at excellent prices!... Compare to the closest competitor Sparco unit... there is no comparison!

Material:	Type 304, stainless steel - 100% USA Made
Finish:	Powdercoated, durable black wrinkle-finish.
Weight:	16 Lbs.
Models:	'00 - '06 E46: Direct fit into E46 M3, also Coupe "Ci" chassis ONLY
Installation:	Bar is mounted to the rear side lap belt mounting points via brackets that are installed once and remain in the car. Support rods are attached to the ends of the main tube while the other end attaches to car at the front lap belt mounting points located at the door sills.
Miscellaneous:	Bar is designed to allow enough seat travel for tall drivers. After initial installation the bar can be removed and reattached in about 15 minutes.

Visit Harness Bars to see additional products in this category.

Brey Krause Harness Mount Bar, BMW E36 Coupe

Thu, 24 Feb 2011 11:54:00 GMT

Brey Krause Harness Mount Bar, BMW E36 Coupe
Buy Now: $649.95

The Only Harness Bar we trust at VAC...

The Brey Krause E36 harness bar has been independently tested and certified by a qualified laboratory to handle the types of forces required by the National Highway Traffic Safety Admin. DOT and SAE J385 Rev. MAR 95, Motor Vehicle Seat Belt Anchorages-Performance Requirements.

Brey Krause bars are easy to install and remove, and use only existing holes and mounting points- these will not damage the car in any way!

Strength requirements for harness mounts are considerably greater than those for harness guide bars since they must support the entire load applied to the belts. With Brey Krause, quality and safety are #1.

Material:	Type 304, stainless steel - 100% USA Made
Finish:	Powdercoated, durable black wrinkle-finish.
Weight:	16 Lbs.
Models:	'93 - '99 E36: fits Coupe Chassis ONLY
Installation:	Bar is mounted to the rear side lap belt mounting points via brackets that are installed once and remain in the car. Support rods are attached to the ends of the main tube while the other end attaches to car at the front lap belt mounting points located at the door sills.
Miscellaneous:	Bar is designed to allow enough seat travel for tall drivers. After initial installation the bar can be removed and reattached in about 15 minutes.

Visit Harness Bars to see additional products in this category.